Turning a Christmas Tree

Nov 19, 2026

If you are looking for a fast, modern holiday woodturning project that showcases natural wood grain, minimalist Nordic-style Christmas trees are hard to beat. Unlike traditional turned trees with curved profiles and heavy ornamentation, this Nordic design relies on clean, straight angles and asymmetrical proportions.

When turned in a mix-and-match set of contrasting hardwoods, they create a striking, contemporary centerpiece for a mantle or holiday table. Best of all, they are quick to turn and make great use of spindle blanks or shop offcuts.

The Golden Rule of Christmas Tree Design

Before mounting your blank, keep one critical design principle in mind: asymmetrical heights, identical angles.

To give these trees their modern, organic look, vary the height and diameter of each tier—avoid dividing the blank into equal thirds. However, the degree of taper on every cone must match. If one tier is steeper or shallower than the tier above or below it, the visual flow breaks and the tree will look “off.” Keep a straightedge or ruler handy at the lathe to check that your cone walls are flat and your angles align.

A collection of wooden turned christmas trees on a wood table surrounded by pine trees

 

Step-by-Step Turning Instructions

Prep and Mount the Blank

Ensure the bottom end of your 3” x 3” blank is cut dead square on a miter saw so it registers cleanly against your chuck.

While you can turn this project between centers or expand a 4-jaw chuck into a Forstner-bit recess, a 3-in-1 screw chuck offers fast mounting and easy remounting if you ever want to re-polish the tree later.

  1. Drill a 1/4” hole in the center of the bottom end. For convenience, use a depth collar on your bit so you don’t drill too deep into the base.
    A drill bit held in a drill chuck drilling into the end of a turning ash blank

  2. Thread the blank onto the screw chuck by hand or with the lathe running at its lowest speed, letting go as soon as the wood seats against the chuck face.
  3. Lock the spindle and snug the blank tight.
  4. Bring up your tailstock with a 60-degree revolving center for support. Apply light pressure—just enough to support the cut without crushing the wood fibers at the top.

Rough to Round and Plane it Smooth

Set your tool rest just below center and start the lathe at 0 RPM, slowly dialing up to around 1,200 RPM once you’re sure the corners clear the rest.

Using a spindle roughing gouge, work from the center outward to knock off the sharp corners, maintaining as much of the 3” diameter as possible. Open-grained woods like ash can splinter along the corners if you take overly aggressive bites, so use light passes. Once the corners are gone, increase the speed to about 1,700 RPM to finish bringing the blank to round.

A turning blank being turned round by a spindle roughing gouge

Switch to a skew chisel (raising the tool rest so the cutting edge meets the wood around the 10 to 11 o’clock position at a 45-degree angle) and bump the speed up to roughly 2,300 RPM. Take light planing cuts to remove the ridges left by the roughing gouge and reveal clean grain.

A spinning blank being turned smooth by a skew chisel

Lay Out the Tiers and Base

With the lathe running slowly, use a pencil to mark your three asymmetrical tiers:

  • Leave roughly 1/4” of waste wood at the tailstock end so the dimple from your revolving center won’t remain on the tip of your finished tree.
  • Make the top tier the longest, the middle tier slightly shorter, and the bottom tier the shortest.
  • At the very bottom (chuck end), plan for a small base step, chamfer, or slight undercut so the tree sits cleanly on a flat surface without rocking.

Shape the Cones (and Match the Tapers)

Use the toe of your skew chisel (or a parting tool) to establish the V-cuts at the base of the top and middle tiers, stepping deeper to define the overhang of each branch layer.

To turn the long, straight cones:

  • Lock your arms against your torso and shift your weight from side to side with your legs. Moving with your body, not just your arms, keeps the bevel riding smoothly and prevents dips or waves in the wood.
  • Instead of staring directly at the cutting edge, look at the top silhouette (“horizon”) of the spinning wood to judge your angle and straightness in real time.
    Turning a wood blank into a tree shape with a skew chisel

  • Stop the lathe periodically and lay a straight edge or ruler along each cone. Plane down any high spots and adjust your cuts until all three tiers share the exact same angle of taper.
    A hand holding a metal ruler along the edge of a wood blank to check for high spots

  • Take a tiny, light pass with your skew to put a micro-chamfer on the sharp bottom rims of each tier so they won’t chip or feel sharp to the touch.

Sanding and Parting Off the Tip

Once your angles are crisp and the surfaces are cleanly planed with a freshly sharpened skew, lower the lathe speed to 900 RPM for sanding.

  • Fold your sandpaper in thirds and hold the top and bottom edges taut, or wrap it around a small foam block, to keep from rounding over your crisp flat faces.
    Hands holding a strip of sandpaper against a turning blank with sawdust flying

  • Because a sharp skew leaves a really smooth surface, you can start directly at 240-grit and finish at 320-grit. Stop the lathe and hand-sand lightly with the grain to erase any radial scratch marks.

To remove the 1/4” waste block at the top, bring the lathe back up to turning speed and make gradual slicing V-cuts with the long point of your skew until only a tiny nub remains. Retract the tailstock, support the tree gently with one hand, and slice cleanly through the remaining fibers. Touch up the tip by hand with 320-grit sandpaper.

Hand supporting the end of turning blank while cutting with a skew chisel

Apply a Natural Finish

To keep the natural pale color of ash without adding an amber tint, apply an abrasive polishing wax like Scratch-Freee directly on the lathe, then buff it off with a clean rag.

Hands holding a white rag with polish onto a turning wood blank

Shop Tip — Watch Out for Metal Dust: Polishing waxes contain fine abrasives. If your rag rubs against the spinning metal collar of your screw chuck and then touches the wood, it will transfer dark metal dust straight into the open grain of light-colored woods like ash or maple. Keep your wax rag well clear of the chuck! (And if you do accidentally smudge the base, you can either take a whisper-thin cleanup cut with your skew—or lean into it and ebonize the whole tree with a propane torch for a dramatic charred finish.)

Man at lathe holding an ash christmas tree

Mixing & Matching Your Set

Once you unscrew the tree from the chuck, stand it next to a few others turned in different species and heights. The contrast between bright ash, warm cherry, and dark walnut highlights the clean Scandinavian geometry—turning a single afternoon at the lathe into a timeless holiday display.

A collection of wooden christmas trees on a wood table